How to Install the TV in RV in Nigeria

Many people buy an RV to have a home-away-from-home feeling no matter where they are. And, what says home more than a high-quality television setup?

Adding a television to your RV provides you with various options for days when there is rain and evenings when you don’t feel like being stranded outside!

How to install Tv in the RV in Nigeria Nigeriantech.com.ng

RV TVs are now of high quality due to the advancement of technology as any TV you’d find in your home. So you can have practically all the same amenities at home but small scale, but how to install a TV in an RV step by step? Let’s find out below.

Generally, to install a TV in the RV, you have to find its place and then install a mount on the wall. Then, drill the holes in the wall, bolt the support to the wall, hang the TV on the support and connect the power and the antenna cables.

Unlike tent camping, RV allows you to have a long-term, comfortable, and dry setup.

Remember a few things when installing a TV in a recreational vehicle. Let’s look below at those variables and learn how to install a TV in an RV step by step!

If you are about to install TV and audio at home, check out this blog for more information.

Know your RV Before You Install The TV

To avoid any sort of problem, the first thing you should do is inspect your RV for a few minutes to get to know how it is wired. Then, before you consider which upgrades to install, you should take a serious note of what level of service and cabling you have installed in your RV.

1. Determine the location of the TV antenna on your roof, and then find out where the coaxial cable is connected to it. While you’re up there, I would recommend double-checking the line along with the connector to ensure that it is in good working order.

2. If you remove the screws and look at the back of the panel, you might notice a small circuit board. If you have this, you should probably need to get a new one because it, the old one, was designed for only analog signals and should need to be replaced with one that also amplifies digital signals.

3. If your video selector box is older, it will most likely need to be replaced with a newer one for better signal reception. Older video selector boxes have coaxial connections and cables that connect to your various TVs. Check the line to your TV for damage and, if possible, trace it back to ensure that it is not crimped at any point along the way. It can significantly reduce the signal quality and bandwidth available to that TV.

4. Your old analog antenna has an amplifier built-in for the old channels, and by replacing it with a new one, you will get one with a more robust amplifier for digital channel reception.

Are There Different Types of TV Mounts for RV?

How to install Tv in RV in nigeria Nigeriantech.com.ng

To understand how to put your TV in your RV, you must first grasp the many types of mounts.

Each type of mount is installed differently, so make sure that you have obtained the correct size TV rear mounting plate. It is critical because it may cause problems in subsequent steps.

Flat wall TV mount

The flat wall TV mount is the most satisfactory solution for achieving a basic low profile and beautiful look for your RV. These mounts allow you to place a flatscreen TV on your RV wall in the same way that you would a picture or a mirror.

The installation process is pretty simple and has an appealing appearance.

Because of the restricted area, the flat wall mount is excellent for smaller RVs. In addition, it has a superb tilt mechanism that allows you to position your TV in any direction in the RV.

Articulating Wall Mount

Many RV owners consider the Articulating TV wall mount one of the most popular RV TV mounts.

They can be easily placed against a wall, and some models can stretch up to 30 inches, allowing you to move your TV from whenever you want.

One of the advantages of this TV mount is that it will enable you to tilt your TV to the left or right. However, this TV mount is typically more expensive than others because of the tilt functions.

The TV mount conveniently folds back and pushes the TV close to the wall when not in use. This mount is popular since it is simple to install and takes up little space on your RV’s wall.

Tilt TV Wall Mount

It allows you to tilt your TV screen up to 45 degrees downward. So, you can achieve an optimal viewing angle without having pain in your neck and can your TV.

And, you will also notice that it reduces the reflection from windows and other sources. The tilting bracket can be placed almost flush against the wall for a sleek, clean look when not in use.

Full Motion TV Mount

The mount has many pivot points, allowing users to extend, swivel, tilt, and rotate their TV. Thus it becomes pretty easy to use.

You can install the TV in a recessed corner, which gives the illusion of a floating TV when extended. It is handy, and this way, users can view the TV from multiple seating positions in a room.

Push the full motion TV bracket back against the wall once you have finished watching.

Fixed TV Wall Mount

It may be the ideal choice for you if you know you’ll be putting your TV precisely at eye level – commonly around 42 off the ground – you won’t be moving your TV, and you don’t need to access the Television’s ports very often.

They are practically flush with the wall, simple to install, and the most cost-effective mounting bracket kind.

Mount-It TV Wall Mount

These wall mounts are best suited for 22 to 42 screen Televisions.
It includes dual wall plates, allowing you to mount your TV in two locations.

Perlesmith RV Lockable TV Mount

The locking process is simple to operate and snaps into place.

  • You can easily unlock it with a quick pull.
  • You can get a maximum tilt up to 15 degrees, and the swivel primarily depends on the size of your Television but is limited to 90 degrees.

InstallerParts Lockable TV Wall Mount

  • It only tilts if you want a more secure TV wall mount for your RV that does not extend or swivel.
  • It tilts 5 degrees up and 15 degrees down while remaining fixed to the 25.6 brackets.

With a load capacity of 100, this locking TV wall mount is ideal for 32 to 50 flatscreen TVs.

Master Mounts 2311L Locking RV TV Mount

  • It employs a chain to unlock the TV from its locked position.
  • This locking mount is best suited for smaller TVs weighing less than 33 lbs. It is suitable for most flatscreen televisions up to 42 inches in size.
  • It swivels 180 degrees and tilts up and down 8 and 12 degrees.

Tools Needed to Install a TV in RV

How to install Tv in RV in Nigeria Nigeriantech.com.ng

In addition to a few sets of hands, you’ll need a few basic tools to complete the task. Let’s take a look at the equipment you should have on hand.

Power Drill

Using a power drill is one of the most efficient and effective ways to guarantee your TV is placed correctly.

The drill will aid in the tightening of screws to the mounting surface. Make sure not to over-tighten them. Otherwise, the wood will split or break.

Bring the entire set with you if you have a drill bit kit. It will prevent you from having to make repeated excursions back and forth between your RV and your tool bag.

Screws and Anchors

Screws and anchors will most likely be required, depending on the surface. Screws can support a significant amount of weight.

Using anchors is also a good idea, especially in soft materials such as drywall and lower-quality wood. When you use an anchor, you prevent the screws from stripping the hole and becoming loose.

Another Person

Although installing a TV in RV does not necessitate assistance, It is still recommended because we have fragile items such as a TV.

A helper or friend can assist you in carrying the TV or obtaining the necessary tools/accessories while you are on the go.

Stud Finder

Having a stud finder on hand can assist you in correctly locating the hidden installation.

A stud locator will also assist you inconsistently in hitting the middle of the stud. It helps make the most substantial and secure connection possible when mounting big goods.

Level

Many TV mount kits come equipped with a level, but if yours doesn’t, keep one on hand because you want your TV to be as leveled as possible.

The size of the level you select is unimportant in this case, but in general, the larger the level, the better.

Tape

A tape is an optional tool that can substitute for a pencil or marker. For example, once you’ve identified an RV stud, you can mark it with tape or something else.

During the pilot drill, this will make it easier to see.

Screw Adhesive

Screw adhesive functions as a thread locker. It closes the remaining gap between the screw thread and the stud by increasing holding power, especially for thinner walls.

Because RVs are constantly in motion and necessitate extra care, It is recommended you make use of screw glue as an additional stability factor when mounting TVs in RVs.

Cable Cover

Most people are not a fan of messy wires moving around inside an RV. There is, however, a simple solution – cable cover.

All cables can be covered, tied, routed through the RV wall, and hidden behind an object.

How to Install the TV in RV?

To Install the TV in your RV, you can follow the steps below:

1. The first step is figuring out the position of a TV in an RV. Next, determine the exact location of the TV on the wall by holding it up to the wall.

Mark the location of the TV using painter’s tape or a pencil.

2. Most RV walls will not have standard “studs.” Instead, you can put pre-installed metal strapping for installing cabinetry, etc.

Regular stud finders are usually very effective in detecting any obstructions behind the walls, but I recommend contacting the manufacturer if you still have doubts.

3. Use a level for the placement confirmation and mark the pilot holes as they hold the mounting bracket to the marked-off spots. Next, remove the wall mount and drill the pilot holes.

4. Secure the TV bracket with mounting screws in the drilled pilot holes while a friend holds the wall bracket in place, or if you can handle it yourself.

5. If the bracket includes a mounting plate for your TV, it connects the TV to the bracket. Connect these using the holes in the back of the TV.

6. Line up the mounting plate on the back of your TV with the bracket. It will hold your Television to the wall.

7. Connect the power wire and all of the additional connections required by your TV. It includes whether or not you have a DVD player or satellite TV.

Chinedu Okeke

Chinedu is the founder of Nigerian Tech. He is a tech enthusiast who has the passion for emerging trends in the tech industry. He is also a professional web content developer.

You may also like...

Leave a Reply

Your email address will not be published. Required fields are marked *